Leaking, Corroded, or Burst Pipes in Lorman, MS? Masters Plumbing Service Fixes It
Pipe failures range from a slow pinhole leak weeping inside a wall to a full main line rupture. Locating the failure precisely — before opening drywall or digging — is the skill that separates a clean, affordable repair from an expensive and destructive guessing operation. Masters Plumbing Service's pipe technicians in Lorman, MS use acoustic listening devices and thermal imaging cameras to find the leak first, then open only what needs to be opened.
Acoustic & Thermal Leak LocationAll Pipe MaterialsPress-Fit & Sweat CapableLicensed in MS
Our Capabilities
4 Things That Define Our Pipe Repair Service in Lorman, MS
Our techs work on every pipe material found in Lorman, MS homes, from pre-1970s galvanized to modern PEX-A crosslinked systems. The repair method matches the pipe.
🔊
Acoustic Leak Detection
Acoustic detection is most effective on pressurized supply lines. Combined with a pressure test to confirm water loss before we start, it tells us both that there's a leak and exactly where it is.
🌡️
Thermal Camera Scanning
We use thermal imaging as a complement to acoustic detection — particularly useful for slab leaks and leaks inside insulated wall cavities where sound transmission is reduced.
🛠️
All Pipe Materials & Joining Methods
Press-fit copper connections — particularly useful for repairs in occupied spaces where open flame is a concern — are available as an alternative to torch sweating where code permits.
🔒
Pressure-Tested Before We Leave
Every supply line repair is pressure-tested before we close the wall or floor. We pressurize the repaired section, hold the test pressure for the required duration, and confirm zero drop before considering the repair complete. You don't find out there's a second leak next week — we find it before we pack up.
Our Pipe Repair Services
Every Pipe Repair Type We Handle in Lorman, MS
Pipe failures have different causes depending on material type, age, water chemistry, and installation history. Here's how we address each category.
Copper
Copper Pipe Repair & Repipe
Copper failures most often involve pinhole corrosion in soft copper tubing from aggressive water chemistry, failed soldered joints, or fatigue cracks at fittings in high-vibration locations. We locate the failure precisely, cut out the failed section, and install either a sweated repair coupling or a press-fit connector — both rated to ASTM B88 standards for potable water service.
Galvanized
Galvanized Pipe Replacement
Galvanized steel pipe was standard in homes built before the 1960s. It corrodes from the inside out — zinc coating depletes, iron oxide (rust) accumulates on the inner wall, progressively narrowing flow and leaching into the water supply. Repairs on severely corroded galvanized are generally temporary; the pipe is failing systemically along its full run.
PEX
PEX Pipe Repair & Extension
PEX is also the material of choice for extending or reconfiguring supply runs during remodel work. Its flexibility reduces fitting count and eliminates the need for torch work inside walls.
Burst Pipes
Burst & Freeze-Damaged Pipe Repair
We also inspect upstream of the burst for additional sections that froze but haven't yet failed — because a partially-thawed line sometimes shows multiple failure points only after pressure is restored.
Slab Leaks
Under-Slab Pipe Leak Repair
Slab leak rerouting is often more cost-effective than direct access, particularly for longer runs or under tiled floors. We present the options honestly with pricing so you can choose based on your priorities.
Full Repipe
Whole-House Repipe Service
When galvanized supply lines are at end of life or polybutylene pipe (recalled for chronic failure) is in the home, a full repipe with PEX or copper is the permanent solution. We run new supply lines through the structure, transition all fixture connections, pressure test the entire new system, and patch access points in walls and ceilings.
Here's how a Masters Plumbing Service pipe repair call plays out in Lorman, MS.
1
Call & Describe — We Shut the Water If Needed
For emergency burst pipe calls, we dispatch immediately. For suspected slow leaks, we schedule at the earliest available slot and confirm before arrival.
2
Pressure Test & Acoustic / Thermal Detection
This detection step routinely saves homeowners $500–$2,000 in unnecessary drywall removal compared to opening walls speculatively.
3
Flat-Rate Quote & Minimal Access Opening
For slab leaks, we present repair, reroute, and lining options with pricing so you can make an informed choice before any concrete is cut.
4
Repair & Pressure Test — Then You're Done
You receive a written summary of what failed, what we installed, and the warranty terms before we leave.
Customer Reviews
Masters Plumbing Service Pipe Repair — How We Handle It
★★★★★
My older home had a copper supply line fail inside an exterior wall. The thermal camera showed the wet zone through the drywall without any cutting. They opened a 10-inch section right at the pinhole, put in a press-fit repair coupling — no torch in my wall — pressure tested, and patched the drywall themselves. Two hours total.
— N. Bergman, Lorman
★★★★★
Had an under-slab leak diagnosed by Masters Plumbing Service with acoustic equipment. They found the leak at 6 feet from the wall — a single copper elbow that had developed a pinhole. Presented three options: direct slab access, reroute through the wall framing above, or copper lining. I chose the reroute — they ran a new PEX line through the crawl space and connected at both ends without touching the slab. Pressure tested, verified no remaining drop. No jackhammering at all.
— O. & R. Adeyemi, Lorman, MS
★★★★★
Pipe burst in a rental property at 2 AM — Masters Plumbing Service's emergency line answered immediately, talked my tenant through the main shutoff, and had a tech there in 45 minutes. Freeze crack in a PEX line in an exterior wall. Repair and insulation wrap done in under two hours. Detailed receipt for insurance documentation. Exactly what I needed as a landlord dealing with a crisis remotely.
— F. Okoro, Lorman, MS
Common Questions
What to Know Before Calling for Pipe Repair in Lorman, MS
Watch your water meter with all fixtures off. If the meter dial is moving or the leak indicator light is turning, water is escaping somewhere in your supply system. Other signs: unexplained increases in your monthly water bill, soft or discolored spots on walls or ceilings, mold or mildew smell in a room without a visible source, or a running sound inside walls when all fixtures are off.
In most cases, the pipe itself needs to be physically accessed to make a durable repair — but the amount of wall we open depends entirely on how precisely we can locate the failure first. With acoustic detection and thermal imaging, we typically open a single, small access point rather than a wide section of wall.
A slab leak is a supply line or drain line failure in a pipe that runs through or under the concrete foundation slab. Supply line slab leaks are the more urgent scenario — pressurized water escaping under the slab saturates the subgrade, can undermine the foundation, and drives significant water bills.
We assess galvanized condition when we're on-site — visible exterior corrosion, interior scale visible at the cut failure point, and water pressure readings all tell us how advanced the system deterioration is. We give you the repair-vs-repipe math honestly so you can make the decision that fits your timeline and budget.
A single localized pipe repair — finding and fixing one failure point — typically takes 1.5–3 hours including detection, access, repair, and pressure testing. Slab leak reroutes run 3–5 hours depending on the routing path and pipe length. A full-house repipe is a multi-day project — typically 2–4 days for a standard single-family home depending on size and pipe count.
Our pipe repair quote includes clean access cuts and leaving the opening ready for patching — with a clean, straight cut that accepts a standard drywall patch. We can typically patch the access opening as part of the job on request, though finish painting and texture matching are typically handled by the homeowner or a drywall contractor for best cosmetic results.
Service Area
Your Local Pipe Repair Specialists in Lorman, MS
Our techs are stocked with the copper, PEX, and CPVC materials most commonly needed in Lorman homes and businesses.
